Amiga Parts

Trapdoor covers snap, floppy buttons vanish, and the drive your A1200 needs was never made to fit it. This collection is the printable answers — each one compared against the other versions of the same part, checked against the designer’s own page, and linked straight to them.

Every entry states the exact machine it fits — an A1200 trapdoor is not an A500 trapdoor, and we say so when a designer confirms a part does not fit. Licenses are shown as the designer published them, and the files always stay on the designer’s page.

Amiga 1200 Back Trapdoor — HDMI, MicroSD and USB

Fits: Amiga 1200 rear trapdoor · built for PiStorm32 setups

The back trapdoor that finishes a PiStorm32 build: HDMI, USB and microSD on the rear panel, with the support designed in.

by rainbowat · MakerWorld

Personal use105 downloads53 prints

Print this: built-in support, no slicer supports needed · hardware: 1x M3x6 screw + nut · needs HDMI + microSD extension cables (see designer’s page)

Get the filesfree, on the designer’s page ↗ Read our verdict →

Commodore Stand for Amiga 500, 600 and 1200 — With Logo

Fits: Amiga 500, 600 and 1200 · also C64C, C128, Plus/4 and C116

One stand for the whole wedge family — A500, A600, A1200 and the 8-bit wedges too — with the Commodore logo in the print.

by stroke.lugaresi · MakerWorld

Standard Digital File License110 downloads69 prints

Print this: 0.2mm layers · 2 walls · 15% infill · about 2.5 hours · PLA, about 95 g

Get the filesfree, on the designer’s page ↗ Read our verdict →

Amiga 1200 Motherboard Shim — Fit an A1200 Board in a PC Case

Fits: Amiga 1200 motherboard · ITX/ATX PC cases

Rehousing an A1200 board in a modern PC case? This shim matches its three screw holes to ITX/ATX mounting. Designer-confirmed: not for the A500.

by madninja · MakerWorld

CC BY-NC-SA9 downloadsRated 5.0

Print this: designer’s profile: 0.8mm nozzle · 0.4mm layers · 2 walls · 15% infill · PLA, about 103 g · prints on 2 plates

Get the filesfree, on the designer’s page ↗ Read our verdict →

2.5-Inch HDD Adaptor for Amiga 1200 Drive Swaps

Fits: Amiga 1200 (designer’s own use) · older machines with non-standard drive hole patterns

Newer 2.5-inch drives are thicker, with holes in the wrong places. This bracket fixes both — the designer used it in an A1200.

by adesillas · MakerWorld

CC BYNo supports

Print this: no supports · no raft · 0.20mm resolution · 20% infill · PLA (designer printed on an Ender 3)

Get the filesfree, on the designer’s page ↗ Read our verdict →

Amiga 1200 Ventilated Latched Trapdoor Cover

Fits: Amiga 1200 · sized to the original Commodore part

The designer printed the other trapdoor covers and watched their catches break — so this one latches with a twist knob instead of a snap. Rated 5/5 on Printables.

by aeberbach · Printables

CC BYVentilated76 downloads

Print this: twist-latch design · no snap catch to break · vents over the accelerator slot

Get the filesfree, on the designer’s page ↗ Read our verdict →

Gotek FlashFloppy OLED & Rotary Mount

Fits: Amiga 1200 and other vintage machines · Gotek drives

A mounting case that gives a FlashFloppy Gotek its OLED screen and rotary dial a proper home on the machine, instead of dangling out of the floppy slot.

by adam.l11 · Printables

CC BYFlashFloppy54 downloads

Print this: pairs with an OLED display and rotary encoder on a FlashFloppy-flashed Gotek

Get the filesfree, on the designer’s page ↗ Read our verdict →